How To Change Out Power Steering Pump 2001 Chevy S10 4.3
How to Install a Chevy Power Steering Pump
by Dan Ferrell
Wikipedia.org
On most Chevy vehicle models, replacing the power steering pump is an easy process. But in some cases, you lot will demand special tools to disassemble certain components. Follow this guide to aid you install a new or rebuilt unit in your Chevrolet vehicle. The procedure is based on the 2000 Chevy Malibu 2.4L and 3.1L engines, which are similar to other models.
2.4L Engine
Stride 1
Park your car in a safety place with plenty room for you to work around the front of the vehicle.
Step ii
Disconnect the black, negative battery cable.
Pace 3
Disconnect the lines from the power steering pump using a tube wrench to avoid damage to the lines and lock nut. Place a shop rag underneath the lines to take hold of dripping fluid from and cap the lines to avoid ability organization contamination.
Footstep 4
Remove the two mounting bolts from the power steering pump using a wrench or ratchet and socket. Lift the pump off the engine compartment.
Step 5
Fix the new power steering pump in place and first the mounting bolts by hand to avert damage to the threads.
Footstep 6
Tighten the power steering mounting bolts; then connect the lines to the pump by mitt first to avert damage to the threads, and then tighten the nuts with the tube wrench.
Connect the black, negative battery cable; fill the steering pump reservoir with steering fluid. Starting time the engine and completely plow the steering bicycle from left to right several times, checking the ability steering fluid level until it reaches the full marking. Turn off the engine.
3.1L Engine
Step 1
Park your car in a condom place with enough room for you lot to work around the front of the vehicle.
Step 2
Remove the bulldoze belt using a serpentine belt tool (come across Tip section at the bottom for more information). Turn the bulldoze chugalug tensioner clockwise using the chugalug tool and disengage the chugalug from the pulleys.
Footstep three
Remove the three ability steering pump mounting bolts using a ratchet, socket and extension, if necessary.
Pace 4
Pull the power steering frontwards then you can reach the electrical connector and unplug it. Also, disconnect the power pressure tubes using a tube wrench to avoid damage to the lines and nuts. You might want to identify a shop rag underneath to catch steering fluid from the lines. Cover the lines to avoid steering system contagion.
Step 5
Place a flooring jack underneath the engine oil pan with a piece of forest on the jack pad to forbid impairment to the pan; then remove the engine mountain nigh the steering pump using a wrench and ratchet and socket.
Step half dozen
Lift the steering pump away from the engine compartment and install the new pump in place.
Step 7
Install the engine mountain and remove the floor jack form underneath the engine. Connect the pump pressure tubes, plug the electrical connector and install the pump mounting bolts.
Install the drive belt and connect the black, negative battery cable. Fill up the power steering pump with steering fluid and purge the steering system. Turn on the engine and completely turn the steering wheel left and correct several times. Go along checking and adding steering fluid to the pump until the air has been purge from the organisation and the steering fluid reaches the full mark on the reservoir.
Tips
- You may hire a serpentine chugalug tool at virtually motorcar parts stores if you exercise not own or cannot afford to buy one at this betoken. Also, depending on the type of bulldoze belt tensioner installed in your Chevrolet model, you might fifty-fifty be able to utilise a box wrench or long handle billow bar with a three/8-inch drive to plow the tensioner.
Things You'll Need
- Serpentine belt tool Ratchet and socket set Tube wrench Shop rags Wrench set Floor jack
Writer Bio
Since 2003 Dan Ferrell has contributed general and consumer-oriented news to television and the Web. His work has appeared in Texas, New Mexico and Miami and on diverse websites. Ferrell is a certified automation and control technician from the Advanced Technology Centre in El Paso, Texas.
More than Articles
Source: https://itstillruns.com/install-chevy-power-steering-pump-4827689.html
Posted by: smitharing1997.blogspot.com
0 Response to "How To Change Out Power Steering Pump 2001 Chevy S10 4.3"
Post a Comment